Q195 Cathode flat steel

Q195 cathode flat steel is used for electrolytic aluminium factory, the low carbon steel has good electrical conductivity. To produce cathode collector bar of electrolytic aluminum is a strict process, because the electrowinning system is heavy DC current, the electroconductivity will decide the cost of Aluminum, so it must have very good electroconductivity, to save power consumption and raise the electrolytic efficiency.

1 Order contents

Contracts or orders placed under this standard should include the following:

standard encdoing;

product name;

Brand number

specification;

weight;

Special technical requirements (such as guide processing, etc.)

The following definitions apply to this standard.

2 brand representation

Flat steel grades are indicated by steel grades and cross-section dimensions, such as Q215-120×198. Q195 – carbon structural steel grade, 120 × 198 – the sectional size of the cathode flat steel.

3 Size, shape, weight and allowable deviation

3.1 The flat steel thickness and its allowable deviation shall comply with the requirements of Table 1.

  Table 1 Thickness tolerance     mm

Thickness	Tolerance
≥50~80	+2.0 -2.5
>80~120	+2.0 -2.0
>120~150	+2.5 -2.5

3.2 The width of the flat steel and its allowable deviation shall comply with the provisions of Table 2.

      Table 2 width tolerance      mm

Width	Tolerance
≥50~100	+0.0 -2.0
>100~200	+0.0 -2.5
>200~300	+0.0 -3.0

3.3 Flat steel length and its allowable deviation

Q195 Cathode flat steel is delivered according to a fixed length, the length of the fixed length shall be specified in the contract, and its allowable length deviation is 0 to +15 mm.

3.4 The bending of the length of the cathode flat bar shall comply with the requirements of Table 3.

Table 3   Curvature   mm

 

3.5 The four corners along the length of flat steel, the arc radius 5mm ~ 15mm.

3.6 After consultation between the supplier and the buyer, special specifications and requirements are ordered according to the agreement between the supplier and the buyer.

3.7 Weight

Q195 Cathode flat steel is delivered according to actual weight. After negotiations between supply and demand sides, they can also be delivered according to theoretical weight. Flat steel measurements are calculated according to nominal dimensions and the specific gravity is calculated at 7.85t/m3.

4 Technical Requirements

4.1 Chemical composition

4.1.1 The chemical composition of the flat steel (smelting analysis) shall comply with the provisions of Table 6.

4.1.2 After negotiations between the supplier and the buyer, other brands than GB/T 700 may also be used, and they must be specified in the contract.

The allowable deviation of the finished chemical composition of the flat steel shall comply with the provisions of GB/T 222.

4.2 Mechanical properties

The mechanical properties do not serve as delivery conditions for Q195 Cathode flat steel.

4.3 Method of manufacture

4.3.1 Smelting

Flat steel raw material is smelted by Oxygen converter of 40T or more

4.3.2 Roll Forming

It is rolled into rectangular strip or thick steel plate by hot rolling and then processed into rectangular flat steel according to the required size by sawing or flame cutting.

4.4 Surface quality

The surface of Q195 Cathode flat steel must not have visible cracks, folds, scabs, inclusions, and pressed iron oxide skin. If the above defects must be removed along the length direction, the clearance depth shall be calculated from the actual size of the flat steel and shall not exceed half of the tolerance.

4.5 Internal quality

Q195 Cathode flat steel cross-section after acid immersion low magnification test, the organization is uniform, there must be visible to the naked eye shrinkage, bubbles, cracks and other defects.

5 Test methods

The inspection items and test methods for each batch of steel shall comply with the requirements.

6 Inspection Rules

6.1 Inspection and Acceptance

The inspection and acceptance of flat steel products are carried out by the supplier’s quality and technical supervision department.

6.2 Group Batch Rules

Flat steel shall be inspected and accepted in batches. Each batch consists of the same brand and the same size as the furnace.

6.3 Sample size and sampling location

The sampling quantity and sampling location of each batch of steel shall comply with the requirements of Table 5.

6.4 Review and Decision Rules

Q195 Cathode flat steel re-inspection and determination rules according to GB/T 17505 regulations.

7 Packaging, Signs, and Quality Certificates

7.1 Flat steel must be delivered in bales. The weight of each bale is determined by the parties to the supply and demand.

7.2 Three bundles shall be bundled for each full length of bundle and shall be firm, fastened, and flush at both ends.

7.3 The flat steel mark and quality certificate shall meet the relevant requirements of GB/T 2101.

Grade: Q195

Standard: GB

Thickness: 20-500mm

Width: 10mm-200mm

Length: 2000~5800mm

Place of Origin: Inner Mongolia, China (Mainland)

Brand Name: Baosteel

Model Number: Q195

Application: Electrolytic aluminium factory Cathode flat steel bar

Technique: Hot Rolled

Special Use: Mold Steel

Product Name: Electrolytic aluminium factory Cathode flat steel bar

Type: Any required size

Shape: Square Bar

Material: Q195

Technology: Hot rolled

Delivery Condition: Slotted

Surface: Plain

Surface treatment: Curved angle

Certificate: Quality certificate

Name: Q195 - carbon structural steel grade

Packaging Details

In bundle can be loaded by forklift

Delivery Time

30 days