Bara de oțel catodică pentru topirea aluminiului
$720.00 $600.00
SAE 1006/Q195 Materiale catodice pentru topirea aluminiului, oțelul cu conținut scăzut de carbon are o conductivitate electrică bună. Pentru a produce bara de colectare catodică din aluminiu electrolitic este un proces strict, deoarece sistemul de electrowinning este curent continuu greu, electroconductivitatea va decide costul aluminiului, deci trebuie sa aiba electroconductivitate foarte buna, pentru a economisi consumul de energie și pentru a crește eficiența electrolitică.
- Descriere
- Detalii rapide
- Ambalare & Livrare
- Anchetă
Cathode steel bar for Aluminum melting is a consumable anode material in the process. They are typically made from very low carbon steel and are designed to provide efficient and effective electrical conductivity during the melting process. We can drill long deep hole and plug pure copper rod to produce the whole set as your request.
Cathode steel bar for Aluminum melting have a square cross-section with round copper insert. The quality of steel and copper insert, their dimensions and its fitting in the finished collector bar should be as below and in accordance with the drawing:
- Physical:
- Steel collector bar tolerance:
Lungime (milimetru) 0 / +10
Lățime (milimetru) -2~+2
Înălțime (milimetru) -2~+2
- Cathode steel bar for Aluminum melting geometrical tolerances
- Angle defect at cut end less than 5 milimetru
- Flatness at cut ends less than 2 milimetru
- Angle defect of cross-section less than 3 milimetru
- Deflection on the whole bar less than 3 milimetru
(Laterally and Vertically)
- Local deflection less than 3 mm per meter
(Laterally and Vertically)
- Flatness less than 3 milimetru
(Transversally and vertically)
- Twist less than 3 mm per meter
- Round off 4-15 milimetru
- Steel collector bar surface condition
- Lateral surfaces: Free or metal pickup and cracks deeper than 3 milimetru
- Surface roughness not projecting by more than 1 milimetru
- Cut by saw (Cutting with shears or oxyacetylene torch are prohibited unless followed by grinding). Cuts must not present manufacturing defects (Necessitating a supplementary grinding).
- No painting on the bar ends.
- Physicochemical characteristics
- Composition of collector bar steel (Gravimetrical analysis)
Cathode steel bar for Aluminum melting application requires a ferrous metal with a relatively low electrical resistivity and a good weldability (De exemplu 1020 Grade or ASTM A29/A29 M-99) and following composition requirement:
Carbon: ≤0.06%
Silicon: ≤0.07%
Manganese: ≤0.45%
Phosphorus: ≤0.03%
Sulphur: ≤0.04%
Azot ≤0,012%.
The steel supplier must supply to the client its proposal with typical steel composition range expected for the following chemical elements: Al, C, Cr, Cu, Si, Mn, Ni, S, P & N
- Cathode steel bar for Aluminum melting inspection
Acceptance of cathode bars takes place in the supplier’s premises and includes:
- A check of the quality control results of the supplier, and especially a check of the analysis certificates guaranteeing that the quality of the bar steel meets the requirements of the specification
- A check of bar dimensions is aspect.
As regards inspection procedures, the word “LOT” means “LOT of material to be inspected”, i.e. All the cathode bars, out of which a sample will be taken to check for compliance with the acceptance criteria.
The cathode bards in a given LOT must be manufactured according to the same process and with the same quality of steel.
NB: When there is no acceptance on site, all the supplier control results must be sent to the client purchasing department before shipping for acceptance.
3.1 Acceptance inspection procedure
The acceptance inspection is performed by a representative of an external organization approved by the client.
Supplier results
Supplier must present results as the beginning of acceptance, including as a minimum:
- The chemical composition
- The dimensional check
- Around-off check
- An angle defect checks (cross section and cut-end)
- A total deflection checks
- A twist checks
All the dimensional and appearance controls are carried out according to a singles sampling scheme for normal inspection (Based on standard ISO 2859 AQL 1.5%).
All results that do not comply with the requirements given must be identified.
When the number of defective bars is less than or equal to the lot acceptance criterion, the lot is in conformity.
When the number of defective bars is equal to or greater than the lot rejection criterion, the lot is not in conformity.
When client’s representative arrives, they check the suppliers results and their measurement apparatus. These results are to be appended to the acceptance report.
As fa as the steel composition in concerned, the lot is rejected if the results of the analysis certificates do not comply with the requirements or if at least one of the specified element results is not supplied.
3.2 Dimensional inspection
The bar length, width and height are checked by the attribute as per standard ISO 2859 by the clients representative. The inspection in performed according to the single sampling scheme for normal or reduced inspection with an AQL of 1.5%.
Each bar is classified “defective” or “not defective”, depending respectively on whether the 3 dimensions comply with the tolerances given or whether one of more of the 3 dimensions are out of tolerance. The defective bars are rejected.
When the number of defective bars is less than or equal to the lot acceptance criterion, the lot is accepted.
When the number of defective bars is equal to or greater than the lot rejection criterion, the number of test specimens has to be increased as described bars from this lot must only be presented again after re-examination of all the parts and elimination of the defective bars.
The dimensions are measured as follows:
- Lungime: Place the bar on horizontal working surface with a retaining edge. Place one of the ends of the bar against the edge and place the set square against the other end. Use a tape measure to determine the overall length of the bar between the edge and set square. Record the length measurement on an inspection sheet.
- Width and height: measure these 2 dimensions at the center of the bar with a caliper gauge. Acord all the results on an inspection sheet, which is appended to the acceptance report.
Remarks: The defective bars are rejected after being taken into account for lot acceptance.
3.3 Geometrical inspection of Cathode steel bar for Aluminum melting
These characteristics are checked by attributers in a single sampling scheme with an AQL of 1.5% each bar in classified “defective” or “not defective”, depending on the results of the 8 measurements that have to be done:
- Bar defective: At least 1 of the 8 measurements is out of tolerance
- Bar not defective: Cel 8 measurements comply with the tolerances.
The defective bars are rejected but counted.
The characteristics are measured as follows:
- Total deflection (2 measurements): This is measured on one horizontal and on one vertical face (concave surfaces). Place a rigid ruler longer than the bar on the surface being checked. It must not be possible to insert the 3 mm thick shim between ruler and bar.
- Local deflection (2 measurements): This is measured on one horizontal and on one vertical face (Concave surfaces). Place a 1 m rigid ruler on the surface being checked. It must not be possible to insert the 3 mm thick shim between ruler and bar. Repeat the operation three times by face to check the entire bar length.
- Angle defect at cut end (2 measurements): The perpendicularity is checked at both ends of the bar along the width and height using a set square and the 5 mm thick shim. It must not be possible to insert the shim between set square and end of bar.
- Angle defect of cross-section (2 measurements): The check is made in the middle of the bar along the width and height using a set square and the 3 mm thick shim. It must not be possible to insert the shim between set square and bar.
The results from all these checks are recorded on an inspection sheet appended to the acceptance report.
- OK: Dimensions within tolerances.
- D*: Dimensions out of tolerance (defective).
- 1: First bar rejected.
3.4 Surface condition inspection of Cathode steel bar for Aluminum melting
The acceptance rules are same as those specified, the surface condition of the sample bars are checked visually. Their aspect must comply with the dimension given. Use the depth gauge to measure the depth of any defects.
The flatness at cut ends (2 measurements) is checked at both ends of the bar using a set square and the 2 mm cylindrical shim. It must not be possible to insert the cylindrical shim between set square and end of bar.
3.5 Acceptance report of Cathode steel bar for Aluminum melting
On completion of acceptance, a report is prepared to include at least the following:
- The references of manufacturer and plant,
- The lot number,
- The bar dimensions,
- The number of bars presented, rejected and accepted.
The acceptance report is signed by the representatives of the client and supplier. The analysis certificates and various supplier and client inspection sheets are appended to the acceptance report and attachments.
- Clasă:
-
SAE 1006 Cathode materials for Aluminum melting
- Grosime:
-
50-150milimetru
- Lățime:
-
50mm-300mm
- Lungime:
-
1000~3000mm
- Locul de origine:
-
Mongolia Interioară, China (Continent)
- Nume de marcă:
-
Baosteel
- Numărul modelului:
-
SAE 1006/Q195
- Aplicație:
-
Electrolytic aluminium factory Cathode bar
- Tehnică:
-
Laminate la cald
- Utilizare specială:
-
Oțel turnat
- Nume produs:
-
Cathode materials for Aluminum melting
- Tip:
-
Orice dimensiune necesară
- Formă:
-
Bar pătrat
- Material:
-
SAE 1006/Q195
- Tehnologie:
-
Laminate la cald
- Condiții de livrare:
-
Fante
- Suprafață:
-
Câmpie
- Tratarea suprafețelor:
-
Unghi curbat
- Certificat:
-
Certificat de calitate
- Nume:
-
SAE 1006/Q195 - Cathode materials or Aluminum melting
- Detalii ambalaj
- În pachet pot fi încărcate cu stivuitorul
- Timp de livrare
- 30 Zile
- Capacitatea de aprovizionare:
- 5000 Ton / tone pe zi
- Port:
- Portul Tianjin
Produse conexe
-
Citeste mai multVizualizare rapidă
Bar colector de oțel pentru instalația de topire din aluminiu
Bara inovatoare de colectare catodică ar trebui să fie din oțel cu conținut foarte scăzut de carbon, este ASTM Grad 1006 oțel cu conținut scăzut de carbon, deoarece oțelul cu conținut scăzut de carbon are o electroconductibilitate bună. În mod normal, conținutul de carbon ar trebui să fie mai mic decât 0.06%, materialul numit SAE 1006, componentele chimice de mai jos:
Carbon ≤0,06%, Siliciu ≤0,07%, Mangan ≤0,45%, Fosfor ≤03%, Sulf ≤0,04%, Azot ≤0,012%.$720.00$600.00 -
Citeste mai multVizualizare rapidă
SWRH72A țaglă de oțel pentru sârmă din oțel cu conținut ridicat de carbon
Putem furniza orice fel de țagle de oțel în cantitate mare cu preț competitiv, în special oțel special, de exemplu: SWRH82B, SWRH72A sau SWRM8.
Dimensiune: 11m × 152mm × 152mm.
Dacă aveți nevoie, Vă rugăm să ne lăsați un mesaj.
-
Citeste mai multVizualizare rapidă
SAE1006 bară din oțel cu conținut scăzut de carbon pentru electrocâștigarea aluminiului
SAE 1006/Q195 Electrowinning catodic de topire din aluminiu este utilizat pentru fabrica de aluminiu electrolitic, oțelul cu conținut scăzut de carbon are o conductivitate electrică bună. Pentru a produce bara de colectare catodică din aluminiu electrolitic este un proces strict, deoarece sistemul de electrowinning este curent continuu greu, electroconductivitatea va decide costul aluminiului, deci trebuie sa aiba electroconductivitate foarte buna, pentru a economisi consumul de energie și pentru a crește eficiența electrolitică.
$720.00$600.00 -
Citeste mai multVizualizare rapidă
Bar colector catod pentru instalația de topire din aluminiu
SAE 1006 Bara colector catodică este utilizată pentru fabrica de aluminiu electrolitic, oțelul cu conținut scăzut de carbon are o conductivitate electrică bună. Pentru a produce bara de colectare catodică din aluminiu electrolitic este un proces strict, deoarece sistemul de electrowinning este curent continuu greu, electroconductivitatea va decide costul aluminiului, deci trebuie sa aiba electroconductivitate foarte buna, pentru a economisi consumul de energie și pentru a crește eficiența electrolitică.
$720.00$600.00 -
Citeste mai multVizualizare rapidă
Bară unghiulară pentru fabricarea turnurilor de transmisie sau construcția navală maritimă
O bară unghiulară, cunoscut și sub numele de L-bar sau fier unghiular, este o componentă structurală din oțel utilizată în mod obișnuit în construcția turnurilor de transmisie și a construcțiilor navale maritime.
În construcția turnurilor de transmisie, Barele unghiulare sunt utilizate ca elemente structurale importante pentru a oferi stabilitate și suport. Ele sunt adesea folosite ca bretele, brațe încrucișate, și elemente diagonale pentru a rezista diferitelor sarcini și forțe pe care turnul le poate experimenta, cum ar fi vântul, gheață, și greutatea liniilor de transport. Barele unghiulare sunt alese pentru rezistența lor, versatilitate, și rentabilitatea în aceste aplicații.
În construcția navală maritimă, Barele unghiulare sunt, de asemenea, utilizate pe scară largă. Ele sunt utilizate pentru diverse aplicații, cum ar fi încadrarea, Rigidizare, și structuri de sprijin. Barele unghiulare asigură integritatea structurală și stabilitatea corpului navei și suprastructurii. Ele sunt utilizate în construcția pereților etanși, Cadre, Punţi, și alte componente critice. Barele unghiulare sunt preferate în construcția navală datorită raportului ridicat rezistență-greutate, ușurința de fabricație, și rentabilitate.$650.00$560.00 -
Citeste mai multVizualizare rapidă
Placă de oțel marină
Standard: CSC
Clasă: 2C, 3C, 4C, 5C, 12MNC, 16MNC, 15MnTiC, 14MnVtirec
Locul de origine: Liaoning, China
Nume de marcă: Yueqi
Numărul modelului: A B D E AH32 AH36 DH32 DH36 EH32 EH36
Tip: Placă de oțel, Placă cu conținut scăzut de aliaj
Tehnică: Laminate la cald
Tratamentul suprafețelor: Sablare și Primer
Aplicație: Placă de expediere
Utilizare specială: Placă de oțel de înaltă rezistență
Lățime: 2000mm-2500mm
Lungime: 6000mm-12000mm
Toleranță: ±2%
Serviciul de procesare: Aplecare, Sudură, Tăiere, Bătaie
Timp de livrare: 45 Zile
Nume produs: Placă de oțel marină
Calitate normală a oțelului material: Ușoară oțel ABS GR. A B D E
Material normal: 2C, 3C, 4C & 5C
Grad de oțel material de înaltă rezistență: AH32 AH36 DH32 DH36 EH32 EH36
Material de înaltă rezistență: Oțel slab aliat 12MnC, 16MnC, 15MnTiC, 14MnVTiReC
Obicei: utilizate pentru construcția de nave și fabricarea structurii corpului navei
MOQ: 300 Tone
Avantaj: Preț competitiv și calitate bună
Margine: 4 tăiere
Certificat: Certificate materiale de certificare de clasă
Capacitatea de aprovizionare: 3000 Ton / tone pe zi
Ambalaj & Livrare
Detalii ambalaj: Pachet în container sau mărfuri în vrac
Port: Portul Tianjin
Timp de pregătire: A se negocia$1,300.00$1,100.00 -
Citeste mai multVizualizare rapidă
Q195 Oțel plat catodic
Oțelul plat catod Q195 este utilizat pentru fabrica de aluminiu electrolitic, oțelul cu conținut scăzut de carbon are o conductivitate electrică bună. Pentru a produce bara de colectare catodică din aluminiu electrolitic este un proces strict, deoarece sistemul de electrowinning este curent continuu greu, electroconductivitatea va decide costul aluminiului, deci trebuie sa aiba electroconductivitate foarte buna, pentru a economisi consumul de energie și pentru a crește eficiența electrolitică.
$720.00$600.00 -
Citeste mai multVizualizare rapidă
Bara colector catodică
SAE 1006 bara catodică ar trebui să fie din oțel cu conținut foarte scăzut de carbon, deoarece oțelul cu conținut scăzut de carbon are o electroconductibilitate bună. În mod normal, conținutul de carbon ar trebui să fie mai mic decât 0.06%, materialul numit SAE 1006
$720.00$600.00 -
Citeste mai multVizualizare rapidă
Q345 bară plată cu șină trasă la rece
Bara plană feroviară este utilizată pentru o mulțime de structură, putem produce orice material și dimensiune ca cererea dvs., de asemenea, poate produce o suprafață netedă bară plană, dimensiunea de mai jos:
10x30x6000mm Q235 bar plat
20x35x6000mm Q235 bar plat
30x40x6000mm Q234 bar plat
(10-30)x(30-120)x6000mm Q235/Q345 bar plat
40x40x6000mm ST52 șină bară plată
60x40x6000mm ST52 șină bară plată
70x40x6000mm ST52 șină bară plată
80x40x6000mm ST52 șină bară plată
-
Citeste mai multVizualizare rapidă
SWRH82B țagle de oțel aparțin oțelului cu conținut ridicat de carbon
Putem furniza orice fel de țagle de oțel în cantitate mare cu preț competitiv, în special oțel special, de exemplu: SWRH82B, SWRH62A/72A sau SWRM8.
Dimensiune: 11m × 152mm × 152mm.
Dacă aveți nevoie, Vă rugăm să ne lăsați un mesaj.